Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.     

Investigation on the anti-reduction mechanism of Ti4+ in high dielectric constant system Ca0.9La0.067TiO3 by doping with Al2O3

Ca_0.9La_0.067TiO₃ (abbreviated as CLT) ceramics doped with different amount of Al₂O₃ were prepared via the solid state reaction method. The anti-reduction mechanism of Ti⁴⁺ in CLT ceramics was carefully investigated. X-ray diffraction (XRD) was used to analyze the phase composition and lattice structure. Meanwhile, the Rietveld method was taken to calculate the lattice parameters. X-ray photoelectron spectroscopy (XPS) was employed to study the valence variation of Ti ions in CLT ceramics without and with Al₂O₃. The results showed that Al³⁺ substituted for Ti⁴⁺ to form solid solution and the solid solubility limit of Al³⁺ is near 1.11 mol%. Furthermore, the reduction of Ti⁴⁺ in CLT ceramics was restrained by acceptor doping process and the Q × f values of CLT ceramics were improved significantly. The CLT ceramic doped with 1.11 mol% Al₂O₃ exhibited good microwave dielectric properties: ε_r = 141, Q × f = 6848 GHz, τ_f = 576 ppm/°C.     

LTE室分高倒流小区解决方案的研究

LTE室分高倒流直接影响室内4G用户的感知，同时较大程度拉低LTE网络驻留率指标。由于室内无线环境的封闭性，室分小区之间的覆盖独立性，仅仅通过参数调整的手段达到降低高倒流的效果非常不明显，因此本文针对目前影响室内用户感知的高倒流问题，从高倒流小区的标准出发，对室分高倒流小区的发现手段，产生原因及解决方案进行详尽地阐述，并针对各类型的高倒流情形提出解决方法，最终提供读者发现、分析及解决室分高倒流小区的有效方案，从而作为研究方法提供给LTE室内小区高倒流问题解决的指导意见     

Delineation of mineral potential zone using high resolution aeromagnetic data over part of Nasarawa State,North Central,Nigeria

Qualitative analysis of aeromagnetic data of part of Nasarawa State had been carried out with the aim of delineating mineral potential zone. The study area is bounded by Longitude 8.0°E – 9.0°E and Latitude 8.0°N – 9.5°N with an estimated total area of 18,150?km². Different filters were used to enhance the short wavelength anomalies which could give preliminary information about the magnetic minerals present in the study area. The total magnetic intensity map shows variation of both highs and lows magnetic signature ranges from ?51.2?nT to 110.4?nT after the removal of IGRF value of 33,000?nT; the highs which is basement dominates the north-eastern and north-western part of the study area which corresponds to Akwanga, Wamba and Nasarawa Eggon; these are areas with promising solid minerals of economic potentials like, gold at Wamba; Tin, Columbite and Tantalite at Akwanga while Granite rocks with possible radioactive elements are in abundance at Nasarawa Eggon. The low magnetic values on the other hand, which is made up of sediment deposition also dominates the southern part of the study area, this area corresponds to Lafia, Doma and Keana; Lafia and Doma host some industrial minerals like Clay, glass Sands and the Salt Brines at Keana. The major high magnetic signature trends east-west. The greenish part of the study area indicates alluvium deposition. The filters used are vertical derivatives, downward continuation and analytic signal. The first and second vertical derivatives; shows structures like lineament that could be the host to minerals present in the study area and it trends NE-SW. The downward continued at the depth of 50?m and 100?m shows the veins where magnetic minerals most especially gold are known to settle along igneous and metamorphic rocks. The analytic signal map shows that magnetic amplitude highs could be found at the northern end with most lineaments delineated also conform to other filter used. The tilt derivative map enhances short wavelength anomalies which could be used to mapped shallow basement structures and mineral exploration targets. The results of these filters agreed largely and since most magnetic minerals are structural controls, it is expected that those lineaments identified, most especially at the northern part, could play host to those minerals aforementioned.     

Effect of ultrasonication treatment and fermentation by probiotic Lactobacillus plantarum strains on goat milk bioactivities

In the present research, the effects of continuous ultrasound treatment (100 W, 30 kHz; 0%, 30%, 60% and 90% amplitudes, 15 min) and fermentation process (37°C, 24 h) on the growth of Lactobacillus plantarum LP3 and LU5 strains and bioactive properties (peptide content, α-amylase and α-glucosidase inhibition, anticancer and antioxidant activities and exopolysaccharide content) of goat milk were investigated. According to our results, the ultrasonication of milk up to 60% amplitude promoted the growth of Lactobacillus strains and enhanced the bioactive properties compared with control during fermentation, while, the ultrasonication at 90% amplitude had negative effects on the mentioned parameters. Exopolysaccharide content, α-amylase inhibition, α-glucosidase inhibition, antioxidant activity and anticancer activity of treated samples at 60% amplitude at the end of fermentation in comparison to its beginning were increased 18.09, 12.79, 12.44, 9.4 and 1.92 folds, respectively. Also, the increase of assayed characteristics was found strain-dependent, so that L. plantarum LP3 was more effective than LU5 strain.     

超临界蒸汽参数对燃气蒸汽联合循环性能影响研究

为进一步提高联合循环效率,参考现有燃气蒸汽联合循环12.5 MPa/568℃亚临界蒸汽参数,提出27 MPa/585℃超临界蒸汽参数,根据燃气蒸汽联合循环计算模型,以397 MW燃气轮机联合循环机组为例,计算了超临界蒸汽参数与两种亚临界蒸汽参数的底循环效率和联合循环效率,并分析对比了3种蒸汽参数的底循环效率对联合循环效率的贡献。研究表明:对于同一燃气轮机,超临界和亚临界中低压蒸汽参数不同时,超临界蒸汽参数的底循环效率比亚临界提高了4.3%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由30.21%增加到32.62%,联合循环净效率增加了2.21%,联合循环机组的输出功率增加了20.38 MW;中低压蒸汽参数相同时,超临界蒸汽参数的底循环效率比亚临界提高了2.87%,蒸汽底循环输出功率占联合循环机组输出功率的百分比由31.16%增加到32.62%,联合循环净效率增加了1.44%,联合循环机组的输出功率增加12.5 MW。     

内插螺旋立式上行管流场及传热性能的实验研究

通过粒子图像测速流场实验与传热实验相结合，研究了内插螺旋立式上行管的螺旋节距、丝径、中径比等结构参数在不同Re下对流场、阻力及传热性能的影响。结果表明，内插螺旋能够有效扰动和混合管内流体，使管内形成多个纵向旋涡的流体结构、增大管壁附近液体涡量，有利于强化传热。当Re相同时，管内平均流速v、Nu和综合换热性能PEC均随丝径增大而增大，随中径比减小而增大；随节距增大，3种参数均出现增大的趋势，节距大于20 mm后开始减小。管内流体的阻力f随丝径和节距增大而减小，随中径比增大而增大。综合比较，在较低Re时，节距p=20 mm、丝径e=1.6 mm、中径比D/d=0.75时综合传热效果最好。     

TLCD基础隔震框架结构的减振控制研究

为了避免和减轻由过大隔震层位移引起的损害,对基础隔震框架结构装设调频液柱阻尼器(tuned liquid column damper,简称TLCD)后混合系统的减振效果进行研究。建立了单层和多层混合控制系统在地震作用下的运动方程,采用TLCD-结构体系转化为调频质量阻尼器(tuned mass damper,简称TMD)-结构体系的等效方法,利用TMD参数优化公式,得到单个TLCD初始设计参数,并采用状态空间方程得到多个TLCD最优设计参数。通过对某8层基础隔震结构进行模拟,证明了该理论设计方法的合理性。该混合结构不仅可以减小隔震层位移和加速度,而且对上部结构位移和加速度反应都能更有效的控制。     

基于双层修正无迹卡尔曼的水下节点定位算法* .txt

摘要：针对水下无线传感网络中运动节点定位精度低的问题，提出了一种新的基于双层修正无迹卡尔曼的水下节点定位算法(DLMUKF)。该算法利用下层无迹卡尔曼滤波算法对节点状态进行预测，根据各信标节点的测距传播时延对预测的节点状态进行修正。运用上层无迹卡尔曼滤波算法对修正后的状态进行新的预测与修正。仿真实验中，DLMUKF算法的平均定位误差约为传统多边定位算法的15%，约为基于无迹卡尔曼滤波（UKF）定位算法的16%，受节点运动时间与速度的影响最小。通过实验证明DLMUKF算法能更充分利用实际距离值，可以有效减小运动节点的定位误差。 .txt